Skoda Fabia

Since 2000 of release

Repair and car operation

7.1.3.1. Removal and installation

THE GENERAL DATA

Fastenings of an arm of cables of a drive of a transmission of type 02Т

1 – a bolt of fastening of an arm; 2 – an arm; 3 – the holder of a tube; 4 – a tube of a hydraulic drive of coupling; 5 – the working cylinder

Removal of levers of a drive to a transmission

1 – a tip of a cable of inclusion of transfer; 2 – the lever of a choice of transfers; 3 – a tip of a cable of a choice of transfers; 4 – a lock ring; 5 – a nut; 6 – the lever of inclusion of transfers; 7 – ползун

Arrangement of the gauge of speed of a drive of a speedometer on a type transmission 02Т

1 – connecting колодка; 2 – the gauge of speed of a drive of a speedometer; 3 – a transmission

The connecting plug of a reception pipe of the muffler on models with a type transmission 02T

1 – a reception pipe of the muffler; 2 – the connecting plug; 3 – a coupling bolt; 4 – the resonator; 5 – the holder; 6 – a nut; 7 – a cross-beam; 8 – a pillow of fastening of the resonator; 9 – теплоизоляционный the screen; 10 – a protective casing Pads the oxygen gauge (ljambda-probe)

Fastening of a "mass" wire to a type transmission 02Т

1 – a bolt; 2 – "a mass" wire; 3 – the switch of light of a backing; 4 – a nut; 5 – an arm

Arrangement of points of fastening of a transmission of type 02Т to the engine

1 – bolt М12х65; 2 – bolt М12х140; 3 – bolt М12х65; 4 – bolt М10x50; 5 – bolt М12х80; 6 – the adjusting plug

---

The prevention

To remove and establish a transmission it is necessary on the lift or a viewing ditch.

---

Removal

PERFORMANCE ORDER

1. Remove the top casing of the engine (subsection 2.1 see). 2. Remove the storage battery and its holder. 3. Disconnect a wire from the traction relay of a starter. 4. Turn away three bolts 1 (fig. of Fastening of an arm of cables of a drive of a transmission of type 02Т) fastenings see and disconnect from a transmission an arm of 2 fastenings of cables of a drive of a transmission. 5. Turn away a bolt of fastening and disconnect the holder of 3 tubes 4 drives of coupling from a transmission. 6. Turn away two bolts of fastening and remove the working cylinder 5 drives of coupling with картера couplings, without disconnecting from it a tube. Fix the working cylinder by means of a wire so that it did not disturb to transmission removal. The prevention After removal of the working cylinder at all do not press a coupling pedal. 7. Remove a lock ring 4 (fig. Removal of levers of a drive to a transmission see), remove the lever 2 choice of transfers and will put it aside together with a cable. 8. Turn away a nut of 5 fastenings, remove the lever of 6 inclusions of transfers and will put it aside together with a cable. 9. Disconnect колодку 1 (the Arrangement of the gauge of speed of a drive of a speedometer fig. see a type transmission 02Т) with wires from the gauge of 2 speeds of a drive of a speedometer. 10. Turn away bolts accessible from above (fig. the Arrangement of points of fastening of a transmission of type 02Т to the engine see) transmission fastenings to the engine. 11. Turn away the top bolt of fastening of a starter. 12. Remove a forward left wheel. 13. Remove локарь niches of a forward left wheel. 14. Remove грязезащитный a guard картера the engine. 15. Having weakened an inhaling of coupling bolts 3 (the Connecting plug of a reception pipe of the muffler fig. see models with a type transmission 02T) collars of fastening of the connecting plug 2, disconnect a reception pipe 1 from the resonator of 4 systems of release of the fulfilled gases. 16. Take out from the holder 5 wire of the oxygen gauge (ljambda-probe). 17. Turn away a forward bottom bolt 1 (fig. Fastening of a "mass" wire to a type transmission 02Т see) transmission fastenings to the engine, thereby having disconnected as well "a mass" wire 2 from a transmission. 18. Disconnect колодку with wires from the switch 3 lights of a backing. 19. Turn away a nut of 4 fastenings and disconnect from a box an arm 5. Will put an arm with wires aside. 20. Remove a starter. 21. Disconnect both drives of wheels from flanges. 22. Disconnect a spherical support from the lever of a forward suspension bracket and a rack from a bar of the stabilizer of cross-section stability. 23. Take away outside a telescopic rack 2 (fig. in subsection 7.2.3 item 10 see) forward suspension bracket, establish between it and a body the wooden prorate 1. Suspend a drive of a wheel by means of a wire, for example, to a spring of a forward suspension bracket. The right drive of a wheel fix as it is possible above. Be thus cautious – do not damage a varnish covering of semiaxes. 24. Turn away three bolts 1 and 3 (fig. in subsection 7.1.2.1 item 26) fastenings see and remove a back support 2 power units. 25. Turn away a bolt of fastening of a transmission to the engine, being over the right flange of a target shaft of differential. 26. Hook on the engine for eyes and pull cables тали, without supposing damage of hoses and wires. 27. Raise the engine a little so that to unload the left support of the power unit, and turn out bolts 2 (fig. in subsection 2.12.7 item 39 see) fastenings of the left support. 28. Lower a transmission 1 so that to get access to bolts of 2 fastenings of an arm of a transmission through a niche of a forward left wheel. Thus watch, that the transmission did not lean against a beam of a forward suspension bracket. Turn away two bolts of 2 fastenings of an arm 3. 29. Turn away the bottom bolts of fastening of a transmission to the engine (fig. the Arrangement of points of fastening of a transmission of type 02Т to the engine see). 30. Take away a transmission from the engine and lower it, inclining in appropriate way and wringing out the engine in the opposite direction.

Installation

PERFORMANCE ORDER

Establish a transmission upside-down. At installation of levers of a drive of a gear change enter ползун 7 (fig. Removal of levers of a drive to a transmission see), established on the lever of a choice of transfers, to gearing with the lever of inclusion of transfer. Check up level and if necessary add oil in a transmission.

The inhaling moments, Нм

Bolt of fastening of an arm to a transmission	40 to tighten on 90
Nut of fastening of the lever of inclusion of transfers	25
Bolt of fastening of cables of a drive of a transmission	25
Bolts 1, 2, 3 and 5 (fig. the Arrangement of points of fastening of a transmission of type 02Т to the engine see) transmission fastenings to the engine	80
Bolt of 4 fastenings of a transmission to the engine	45