Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
- 7. Transmission and a running gear
   - 7.1. A transmission
      7.1.1. Technical characteristics of transmissions (КП)
      + 7.1.2. Type 002 transmission
      - 7.1.3. A type transmission 02T
         7.1.3.1. Removal and installation
         7.1.3.2. Check of level and oil pouring in a transmission
         7.1.3.3. Replacement of a cover of the lever of a gear change
         7.1.3.4. Removal and installation of a drive of a gear change
         7.1.3.5. Dismantling and assemblage of the mechanism of a gear change
         7.1.3.6. Adjustment of a drive of a gear change
         7.1.3.7. Removal and installation of a drive of forward wheels
   + 7.2. A forward suspension bracket
   + 7.3. A back suspension bracket
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes


75d7f213

7.1.3.4. Removal and installation of a drive of a gear change
THE GENERAL DATA

Detachment of cables of a drive from levers of a transmission of type 02Т

1 – a wrench;

2 – flat-nose pliers;

3 – a cable of inclusion of transfers;

4 – a cable of a choice of transfers;

5 – a spherical finger

PERFORMANCE ORDER
1. Remove the storage battery and an arm of its fastening.
2. Disconnect both cables 3 and 4 from levers on a transmission. For this purpose, using a wrench 1 as the lever and having enclosed under it flat-nose pliers 2 as a support, remove tips of cables from spherical fingers of 5 levers.
3. Turn away three bolts 1 (fig. of Fastening of an arm of cables of a drive of a transmission of type 002 see) fastenings of an arm of 2 cables to a transmission.
4. Remove a cover of the lever of a gear change (subsection 7.1.2.4 see).
5. Accurately having hooked a screw-driver, remove facing 5 (fig. of the Detail of fastening of a cover of the lever of a gear change see) floor console.
6. Turn on two nuts of 1 forward fastening of the case of the mechanism of 2 gear changes (subsection 7.1.2.5 see).
7. Turn away eight nuts 6 (the Connecting plug of a reception pipe of the muffler fig. see models with a type transmission 02T) fastenings and remove a cross-beam 7.
8. Take out from the holder 5 wire of the oxygen gauge (ljambda-probe).
9. Turn away two screws of fastening and remove a protective casing 10 Pads a ljambda-probe.
10. Having weakened an inhaling of coupling bolts of 3 collars of fastening of the connecting plug 2, disconnect a reception pipe 1 from the resonator of 4 systems of release of the fulfilled gases.
11. Disconnect the resonator from a pillow of 8 fastenings of a suspension bracket.
12. Disconnect a reception pipe 17 (fig. System of release of the fulfilled gases of the engine of 1,0 l, 37 kw and 1,4 l, 50 kw see) from pillows 8.
13. Remove теплоизоляционный the screen 9 (the Connecting plug of a reception pipe of the muffler fig. see models with a type transmission 02T).
14. Turn away a bolt 16 (fig. of the Detail of the mechanism of a gear change) fastenings of the case 14 mechanisms of a gear change see and remove a drive of a gear change from the car.
15. Replace the damaged or strongly pressed out sealing lining 11. The lining 11 executed with a glutinous layer, is pasted on the case of the mechanism of a gear change.
16. Establish a gear change drive upside-down. Before connection of cables to levers grease with a thin layer консистентной greasings of the plug 2 (subsection 7.1.2.5 see) tips, without supposing greasing hit on tip consolidation. After installation adjust a gear change drive.

The inhaling moments, Нм

Nuts of forward fastening of the case of the mechanism of a gear change
25
Bolt of the case of the mechanism of a gear change
25
Bolts of fastening of an arm of cables to a transmission
25