Skoda Fabia

Since 2000 of release

Repair and car operation


Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
- 11. A body
   11.1. Removal and installation of a skeleton of a motor compartment
   + 11.2. A forward door
   - 11.3. A back door
      11.3.1. Removal and installation
      11.3.2. Removal and installation of the external handle of the lock
      11.3.3. Removal and lock installation
      11.3.4. Replacement of sealants
   + 11.4. Seats
   + 11.5. Seat belts
   11.6. Removal and installation of the panel of devices
   11.7. Removal and tjagovo-drawbar installation
   + 11.8. A heater
+ 12. Electroschemes


75d7f213

11.3.3. Removal and lock installation
THE GENERAL DATA

Removal of the internal panel of a back door

 1 – a bolt of fastening of the lock;

2, 3 – screws of fastening of the internal panel;

4 – заглушка;

5 – the internal panel of a door;

6 – распорный a pin;

7 – an adjusting pin;

8 – directing window lifterа;

9 – a cable window lifterа

Installation of glass of a back door

 1 – ползун;

2 – directing window lifterа;

3 – glass;

4 – an adjusting pin;

5 – распорный a pin

On the internal panel of a door are put the lock, window lifter and динамик.

PERFORMANCE ORDER
1. Disconnect a wire from the plug - the storage battery.
2. Shift a protective cover and disconnect Pads with wires from a body rack.
3. Remove a door upholstery.
4. Remove the external handle of a door.
5. Having hooked a screw-driver, take out заглушку 4 (fig. Removal of the internal panel of a back door see) of the internal panel of 5 doors.
6. Lower door glass so that to get access to an adjusting pin of 7 glasses.
7. Screw саморез in diameter 5 mm and length approximately 70 mm in распорный a pin 6 (internal). Pull out for саморез распорный a pin.
8. Screw саморез in diameter 8 mm and length approximately 80 mm in an adjusting pin 7. Pull out for саморез an adjusting pin, having taken away by means of a screw-driver a cable 9 window lifterа.
9. Lift hands glass and fix it in this position, having inserted a wedge between glass and the door panel.
10. Turn on at an end face of a door two bolts of 1 fastening of the lock.
11. Turn away screws of 2 and 3 fastenings of the internal panel of a door.
12. Remove the internal panel 5, having deduced it towards a forward part of a door.
13. Pull out a plait of wires from a door.
14. Remove the lock from the internal panel and disconnect from it draughts.
15. Will put the door lock upside-down.
16. For connection of glass 3 (fig. Installation of glass of a back door see) to ползуну 1 window lifterа insert into an aperture has flown down an adjusting pin 4, and in it – распорный a pin 5. Be convinced that pins act on identical distance from both parties of glass.
17. Establish the internal panel of a door. At its fastening by the first wrap screws 2 (fig. Removal of the internal panel of a back door see).
18. Lower glass 3 (fig. Installation of glass of a back door) down to an emphasis of pins 4 and 5 in ползун 1 see and easy blow of a hand on the top edge of glass fix glass in ползуне.