Skoda Fabia

Since 2000 of release

Repair and car operation

7.1.2.5. Removal and installation of a drive of a gear change

THE GENERAL DATA

Detachment of cables of a drive from levers of a transmission of type 002

1 – a wrench; 2 – a cable of inclusion of transfers; 3 – a cable of a choice of transfers; 4 – a spherical finger

Details of the mechanism of a gear change

1 – a lock ring; 2 – the top plug; 3 – a spring; 4 – the bottom plug; 5 – a bolt of fastening of a cover; 6 – a hinge cover; 7 – a hinge holder; 8 – the hinge loose leaf; 9 – directing the lever; 10 – шумоизоляционная a washer; 11 – a lining; 12 – the gear change lever; 13 – the rubber buffer; 14 – the case of the mechanism of switching; 15 – the left plug of an axis;

16 – a bolt of the bottom fastening of the case of the mechanism; 17 – an axis; 18 – the directing plug; 19 – a returnable spring; 20 – the intermediate lever of a choice of transfers; 21 – a bolt of fastening of the lever; 22 – a cover; 23 – a cable of a choice of transfers; 24 – a cable of inclusion of transfers; 25 – a lock ring; 26 – a nut; 27 – the right plug of an axis; 28 – a lock ring of an axis

PERFORMANCE ORDER

1. Remove the storage battery and an arm of its fastening. 2. Disconnect both cables 2 and 3 (fig. the Detachment of cables of a drive from levers of a transmission of type 002 see) from levers on a transmission. For this purpose, operating with a wrench 1 as the lever, remove tips of cables from spherical fingers of 4 levers. 3. Turn away three bolts 1 (fig. of Fastening of an arm of cables of a drive of a transmission of type 002 see) fastenings of an arm of 2 cables to a transmission. 4. Remove the handle with a cover of the lever of a gear change (subsection 7.1.2.4 see). 5. Accurately having hooked a screw-driver, remove facing 5 (fig. of the Detail of fastening of a cover of the lever of a gear change see) floor console. 6. Turn on two 1 nuts of forward fastening of the case of the mechanism of 2 gear changes. 7. Turn away eight nuts 5 (the Connecting plug of a reception pipe of the muffler fig. see models with type 002 transmission) fastenings and remove a cross-beam 6. 8. Having weakened an inhaling of coupling bolts of 3 collars of fastening of the connecting plug 2, disconnect a reception pipe 1 from the resonator of 4 systems of release of the fulfilled gases. 9. Disconnect the resonator from a pillow of 7 fastenings of a suspension bracket. 10. Disconnect a reception pipe 17 (fig. System of release of the fulfilled gases of the engine of 1,0 l, 37 kw and 1,4 l, 50 kw and fig. System of release of the fulfilled gases of the engine of 1,4 l, 55 and 74 kw see) from pillows 8. 11. Remove теплоизоляционный the screen 8 (the Connecting plug of a reception pipe of the muffler fig. see models with type 002 transmission). 12. Turn away a bolt 16 (fig. of the Detail of the mechanism of a gear change) fastenings of the case 14 mechanisms of a gear change see and remove a drive of a gear change from the car. 13. Replace the damaged or strongly pressed out sealing lining 11. The lining 11 executed with a glutinous layer, is pasted on the case of the mechanism of a gear change. 14. Establish a gear change drive upside-down. Before connection of cables to levers grease with a thin layer консистентной greasings of the plug of 2 tips, without supposing greasing hit on consolidation of a tip 1. After installation adjust a gear change drive.