Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
- 11. A body
   11.1. Removal and installation of a skeleton of a motor compartment
   + 11.2. A forward door
   + 11.3. A back door
   + 11.4. Seats
   + 11.5. Seat belts
   11.6. Removal and installation of the panel of devices
   11.7. Removal and tjagovo-drawbar installation
   - 11.8. A heater
      11.8.1. Removal and installation of the central snuffled on the panel of devices
      11.8.2. Removal and installation of a lateral nozzle on the panel of devices
      11.8.3. Removal and lattice installation blowing lateral glass
      11.8.4. Replacement of a filtering element of a heater
      11.8.5. Replacement of the additional resistor
      11.8.6. Removal and installation of the fan of a heater
      11.8.7. Removal and installation of the control panel by a heater
      11.8.8. Replacement of cables of a drive of a heater
      11.8.9. Removal and installation of a radiator of a heater
      11.8.10. Removal and heater installation
+ 12. Electroschemes


75d7f213 123movies provides high-quality streaming for an immersive viewing experience.

11.8.9. Removal and installation of a radiator of a heater
THE GENERAL DATA

Heater radiator

1 – a casing;
2 – an electroheating element;
3 – a heater radiator;
4 – a label;
5 – a heater sealant in gathering;
6 – a board sealant передка;
7 – a sealing ring;
8 – a radiator branch pipe;
9 – a bolt;
10 – "a mass" wire;
11 – connecting колодка;
12 – a forward clamp of a casing

Connection of hoses to a heater radiator

1 – a taking away hose;

2 – a bringing hose;

3 – a collar;

4 – a radiator branch pipe;

5 – a bolt

Removal of a casing of a radiator of a heater

1 – spring скобы;

2 – a casing;

3 – an adapter of the bottom air line

On a part of models the electroheating element of a heater which in addition warms up air is established. The element joins the block of engine management depending on temperature of air and a cooling liquid and generator loading at the established handle on the control panel a heater on the maximum heating.

PERFORMANCE ORDER
1. Disconnect a wire from the plug - the storage battery.
2. Remove the floor console.
3. Merge a liquid from system of cooling of the engine or press taking away 1 (fig. Connection of hoses to a heater radiator see) and bringing 2 hoses of a radiator of a heater (if the heater radiator acts in film for replacement, it is necessary to merge a liquid).
4. From outside a motor compartment mark position of a branch pipe 4 heaters and turn away a bolt of 5 its fastenings. Take out a branch pipe and together with hoses put aside.
5. Muffle apertures in a radiator 3 (fig. a heater Radiator see) heater.
6. On models with an electroheating element 2 disconnect колодку 11 with wires from a plait on the left side of a heater and "a mass" wire 10.
7. Remove an adapter 3 (fig. Removal of a casing of a radiator of a heater see) bottom air line.
8. Remove spring скобы 1 fastenings of a casing of a radiator of a heater from three parties.
9. Lower and shift on itself a casing 2 radiators of a heater to deduce from gearing its forward clamp 12 (fig. a heater Radiator see).
10. Take out a casing of 1 radiator of a heater from under the panel of devices on the right side.
11. Take out a radiator 3 heaters from a casing 1.
12. Replace the sealing rings torn or lost elasticity 7 branch pipes.
13. Establish a heater radiator upside-down. Thus pay attention that the label 4 on it, specifying bringing and taking away directions, should be from above. Establish a branch pipe according to earlier made marks, densely having inserted it into a sealant 6 on a board передка.
14. Check up level and if necessary add cooling liquid (at replacement of a radiator of a heater fill in a new liquid in system of cooling of the engine).

The moments of an inhaling of a bolt of fastening of branch pipes of the heat exchanger – 20 Нм.