Skoda Fabia

Since 2000 of release

Repair and car operation


Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
- 9. Brake system
   + 9.1. Pedal knot
   9.2. The vacuum amplifier
   9.3. The main brake cylinder
   9.4. A pressure regulator (on models without ABS)
   + 9.5. The brake mechanism of a forward wheel of type FS III
   + 9.6. The brake mechanism of a forward wheel of type FS II
   + 9.7. The brake mechanism of a back wheel (drum-type)
   + 9.8. The brake mechanism of a back wheel (disk)
   + 9.9. A lay brake
   - 9.10. Antiblocking system (ABS)
      9.10.1. Check of electroconducting ABS
      9.10.2. Removal and installation of the block of management
      9.10.3. Replacement of the block of management
      9.10.4. Replacement of a wire of the gauge of frequency of rotation of a wheel
      9.10.5. Replacement of the gauge of frequency of rotation of a wheel
      9.10.6. Replacement of touch rings of gauges of frequency of rotation of wheels
      9.10.7. Removal and installation of the switch of a signal of braking
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes


75d7f213

9.10.4. Replacement of a wire of the gauge of frequency of rotation of a wheel
THE GENERAL DATA

Removal of a cover connecting Pads

 1 – connecting колодка;

2 – a screw-driver;

3 – a cover

Detachment of a plait of wires from Pads the block of management ABS

 1 – connecting колодка;

2 – a clamp;

3 – a screw-driver

Fastening of a wire of the gauge of frequency of rotation of a forward wheel

 1 – connecting колодка;

2 – the holder;

3 – a wire
The prevention

Wires ABS экранированные and to repair are not subject

In the given section replacement of wires of gauges of forward wheels is described. As for replacement of wires of gauges of back wheels the special tool and connecting plugs of wires is necessary, this work is recommended to be spent at servicing deport.

PERFORMANCE ORDER
1. Remove the top casing of the engine (subsection 2.1 see).
2. On models with the diesel engine of 1,9 l, 74 kw remove an air line воздухонаддува, and also a hose between an inlet pipe of the engine and the top air line.
3. Put forward a clamp 2 (fig. the Detachment Pads from the block of management ABS) Pads see and, having pulled upwards, disconnect колодку 3 from the block of 1 management.
4. Having hooked a screw-driver 2 (fig. Removal of a cover connecting Pads see), uncover 3 Pads.
5. By means of a screw-driver 3 (fig. the Detachment of a plait of wires from Pads the block of management ABS see) move a clamp 2 violet colours in a direction specified by an arrow to release wires in колодке.
6. Separate a plait of wires.
7. Push out corresponding wires from Pads. Numbers of contacts are resulted on fig. Numbering of contacts (1–42) connecting Pads the block of management ABS and in the tab. of the Chain connected to contacts Pads.
8. Remove a corresponding wheel.
9. Disconnect колодку 1 (fig. Fastening of a wire of the gauge of frequency of rotation of a forward wheel see) with wires from the gauge of frequency of rotation of a wheel.
10. Take out a wire 3 of holders 2.
11. Establish a wire upside-down.
12. After wire fastening in holders twist a steering wheel against the stop to the right and to the left to be convinced that the wire does not stretch and for what does not cling.
13. At wire connection to колодке the management block track, that wire isolation has been inserted against the stop into an aperture Pads. A braid of a plait of wires fix new collars.