Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
- 4. The power supply system
   4.1. Removal and installation of the air filter
   4.2. Replacement of a filtering element of the air filter
   4.3. Replacement of the gauge of the index of level of fuel
   4.4. Removal and installation of a fuel tank
   4.5. Check of the air valve
   4.6. Check of the gravitational valve
   4.7. Replacement of the fuel filter
   4.8. Check of the valve of heating of fuel
   4.9. Replacement of an adsorber of system of catching of steams of fuel
   4.10. Replacement of a fuel radiator
   4.11. Removal and installation of the vacuum pump of the diesel engine
   4.12. Removal and installation of an inlet pipe of the engine
   4.13. Removal and installation of a pedal of an accelerator
   + 4.14. Removal and installation of atomizers
   4.15. Check of a feed circuit of atomizers of the petrol engine
   4.16. Check of resistance of a pump-atomizer
   4.17. Check of candles накаливания the diesel engine of 1,9 l, 47 kw
   4.18. Check of a feed circuit of candles накаливания
   4.19. Check of the gauge of temperature of a cooling liquid
   4.20. Check of the gauge of temperature of air arriving in the engine
   4.21. Check of the gauge of temperature of fuel of the diesel engine of 1,9 l, 74 kw
   4.22. Check of the gauge of frequency of rotation of a cranked shaft
   4.23. Check of a drive throttle заслонки
   4.24. Check of the gauge of position of a camshaft
   4.25. Check элекромагнитного the valve recycling the fulfilled gases
   4.26. Check of the relay of the fuel pump of engines of 1,4 l, 55 and 74 kw
   4.27. Check of the electromagnetic valve of a purge of an adsorber
   4.28. Removal and installation турбокомпрессора
   4.29. Removal and installation of an intermediate cooler of air
   4.30. Check of the valve of pressure of pressurisation
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
+ 8. A steering
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes


75d7f213

4.12. Removal and installation of an inlet pipe of the engine
THE GENERAL DATA

PETROL ENGINES of 1,0 l, 37 kw And 1,4 l, 50 kw

Inlet pipe of petrol engines of 1,0 l, 37 kw and 1,4 l, 50 kw

1 – a fuel stage;
2 – a bolt of fastening of the case throttle заслонки;
3 – the case throttle заслонки;
4 – a protub of the case throttle заслонки;
5 – an inlet pipe;
6 – a lining of an inlet pipe;
7 – a nut of fastening of an inlet pipe;
8 – the gauge of pressure and air temperature;
9 – a bolt of fastening of the gauge;
10 – the union of a hose of ventilation картера;
11 – the union of a hose of the electromagnetic valve of a purge of an adsorber;
12 – a bolt of fastening of a fuel stage

PERFORMANCE ORDER
1. Disconnect a wire from the plug - the storage battery.
2. Remove the top casing of the engine (subsection 2.1 see).
3. Turn away three bolts of fastening and remove an inlet branch pipe from the case 3 (fig. the Inlet pipe of petrol engines of 1,0 l, 37 kw and 1,4 l, 50 kw see) throttle заслонки.
4. Disconnect колодку with wires from a drive throttle заслонки.
5. Disconnect from the union 10 hose of ventilation картера.
6. Disconnect from the union 11 hose of a purge of an adsorber.
7. Disconnect колодку with wires from the gauge 8.
8. Disconnect топливопровод from a fuel stage 1.
9. Disconnect Pads with wires from atomizers.
10. Turn away six nuts of 7 fastenings and remove an inlet pipe 5 with linings 6.
11. If necessary turn away bolts 2 and remove the case 3 throttle заслонки, turn away bolts 12 and remove a fuel stage 1, having pulled it upwards that atomizers left apertures in an inlet pipe, turn away a bolt 9 and remove the gauge 8.
12. Establish an inlet pipe upside-down. Thus replace linings 6 and 4.

PETROL ENGINES of 1,4 l, 55 And 74 kw

Inlet pipe of petrol engines of 1,4 l, 55 and 74 kw
1 – the case throttle заслонки;
2 – a sealing ring of the case;
3 – a bolt of fastening of the case throttle заслонки;
4 – a bolt of fastening of an inlet pipe;
5 – an inlet pipe;
6 – a lining of an inlet pipe;
7 – a directing plate of the gauge;
8 – sealing rings of the gauge;
9 – the gauge of pressure and air temperature;
10 – a bolt of fastening of the gauge

PERFORMANCE ORDER
1. Disconnect a wire from the plug - the storage battery.
2. Remove the top casing of the engine (subsection 2.1 see).
3. Disconnect from the case 1 (fig. the Inlet pipe of petrol engines of 1,4 l, 55 and 74 kw see) throttle заслонки an air line of the air filter.
4. Disconnect a hose of a purge of an adsorber from the case 1 throttle заслонки.
5. Disconnect from the case 1 throttle заслонки колодку with wires.
6. Turn away two bolts of fastening and disconnect from an inlet pipe 5 tube recycling the fulfilled gases.
7. Disconnect колодку with wires from the gauge of 9 pressure and air temperature.
8. Disconnect Pads a plait of atomizers from a plait of wires.
9. Disconnect топливопровод from a fuel stage.
10. Turn away six bolts of 4 fastenings and remove an inlet pipe 5.
11. If necessary turn away bolts of fastening and remove from an inlet pipe a fuel stage, the case 1 throttle заслонки and the gauge of 9 pressure and air temperature.
12. Establish an inlet pipe upside-down. Thus replace a sealing ring of 2 cases throttle заслонки irrespective of its condition and in case of damage – linings 6, sealing rings 8 and directing plate 7 gauges.

The DIESEL ENGINE of 1,9 l, 74 kw

Inlet pipe of the diesel engine of 1,9 l, 74 kw
1 – an inlet pipe;
2 – a sealing ring of the case throttle заслонки;
3 – the case throttle заслонки;
4 – the valve recycling the fulfilled gases;
5 – a hose to the vacuum pump;
6 – the valve throttle заслонки;
7 – a bolt of fastening of the case throttle заслонки;
8 – a bolt of fastening of an arm;
9 – a drive arm;
10 – a drive throttle заслонки;
11 – a bolt of fastening of a tube;
12 – a tube recycling the fulfilled gases;
13 – a tube lining

PERFORMANCE ORDER
1. Disconnect a wire from the plug - the storage battery.
2. Remove the top casing of the engine (subsection 2.1 see).
3. Disconnect from the case 3 (fig. the Inlet pipe of the diesel engine of 1,9 l, 74 kw see) throttle заслонки an air line of the air filter.
4. Disconnect a hose from the valve 4 recycling the fulfilled gases.
5. Disconnect a vacuum hose from a drive 10 throttle заслонки.
6. Turn away two bolts of 11 fastenings and disconnect a tube 12 from the case 3 throttle заслонки. Remove a lining 13.
7. Turn away bolts of fastening and remove an inlet pipe 1 and a lining of an inlet pipe.
8. If necessary turn away bolts 7 and remove from an inlet pipe the case 3 throttle заслонки.
9. Establish an inlet pipe upside-down. Thus it is necessary to replace a lining of an inlet pipe, a sealing ring 2 and a lining 13.

The DIESEL ENGINE of 1,9 l, 47 kw

Inlet pipe of the diesel engine of 1,9 l, 47 kw
1 – bolts of fastening of the valve;
2 – a sealing ring of the case throttle заслонки;
3 – the case throttle заслонки;
4 – a bolt of fastening of the case;
5 – a branch pipe of a hose of ventilation картера;
6 – a bolt of fastening of an inlet pipe;
7 – a lining of an inlet pipe;
8 – an inlet pipe;
9 – a valve lining;
10 – the valve recycling the fulfilled gases

PERFORMANCE ORDER
1. Disconnect a wire from the plug - the storage battery.
2. Remove the top casing of the engine (subsection 2.1 see).
3. Disconnect from the case 3 (fig. the Inlet pipe of the diesel engine of 1,9 l, 47 kw see) throttle заслонки an air line of the air filter.
4. Disconnect колодку with wires from the case 3 throttle заслонки.
5. Disconnect a hose from the valve 10 recycling the fulfilled gases.
6. Turn away six bolts of 6 fastenings and remove an inlet pipe 8 with a lining 7.
7. If necessary remove from an inlet pipe the case 3 throttle заслонки and the valve 10 recycling the fulfilled gases, having turned away bolts 4 and 1.
8. Establish an inlet pipe upside-down. Thus replace a lining 7 inlet pipes, a lining 9 valves recycling the fulfilled gases and a sealing ring of 2 cases throttle заслонки.

The inhaling moments, Нм

Bolt of fastening of the case throttle заслонки
10
Nut of fastening of an inlet pipe
25
Bolt of fastening of an inlet pipe
20
Bolt of fastening of the gauge of pressure and temperature of air of engines of 1,0 l, 37 kw and 1,4л, 50 kw
10
The same of engines 1,4л, 55 and 74 kw
3
Bolt of fastening of a fuel stage of engines of 1,0 l, 37 kw and 1,4л, 50 kw
20
The same of engines 1,4л, 55 and 74 kw
10
Bolt of fastening of an arm of a drive throttle заслонки
10
Bolt of fastening of a tube recycling the fulfilled gases of diesel engines of 1,9 l, 74 kw
25
The same petrol engines of 1,4 l, 55 and 74 kw
10
Bolt of fastening of the valve recycling the fulfilled gases
25