Skoda Fabia

Since 2000 of release

Repair and car operation



Shkoda Fabija
+ 1.1. The car description
+ 2. The engine
+ 3. Greasing system
+ 4. The power supply system
+ 5. Cooling system
+ 6. System of release of the fulfilled gases
+ 7. Transmission and a running gear
- 8. A steering
   8.1. Removal and steering wheel installation
   8.2. Removal and installation of returnable and contact rings in gathering
   + 8.3. A steering column
   + 8.4. The steering mechanism (without the amplifier)
   - 8.5. The steering mechanism (with the amplifier)
      8.5.1. Replacement of a tip of steering draught
      8.5.2. Removal of the steering mechanism
      8.5.3. Installation of the steering mechanism
      8.5.4. Replacement of steering draught
      8.5.5. The pump unit
      8.5.6. Check of electric chains of the amplifier of a steering
      8.5.7. Replacement of the gauge of the amplifier of a steering
      8.5.8. Replacement of highways of system of the amplifier of a steering
      8.5.9. Check of level of a working liquid
      8.5.10. Refuelling and removal of air from hydraulic system
      8.5.11. Check and adjustment of corners of installation of wheels
+ 9. Brake system
+ 10. An electric equipment
+ 11. A body
+ 12. Electroschemes


75d7f213

8.5.8. Replacement of highways of system of the amplifier of a steering
PERFORMANCE ORDER
1. For convenience of work remove the forward buffer.
2. Turn away a cover 9 (fig. Elements of the hydraulic amplifier of a steering) a receiver see and through a bulk mouth remove by means of a rubber pear a working liquid from a receiver.
3. Remove forward wheels.
4. Remove локарь niches of a forward left wheel.
5. Take out a returnable highway 3 of three holders 4.
6. Wring out a spring latch and open the holder 1 (fig. Extraction of a wire and highways from the holder see). Take out from it pressure head 3 and returnable 2 highways.
7. Unclench by means of flat-nose pliers a collar 5 (fig. Connection of highways to the pump unit see) and accurately disconnect a returnable highway 4 from the union of the pump unit.
8. Turn away a nut of 2 fastenings and disconnect a pressure head highway 3 from the pump unit.
9. Muffle the union and a carving aperture of the pump unit.
10. Disconnect a back support 10 (Fastening of the steering mechanism fig. see the car (without the amplifier)) the power unit from a transmission, having turned away two bolts of 9 fastenings (bolts it is necessary to replace new).
11. Lower a beam of a forward suspension bracket (subsection 7.2.5 see) approximately on 40 mm. Thus do not suppose damage of a wire of the gauge of the amplifier of a steering (for reliability the gauge wire can be disconnected from the pump unit).
12. Turn away a hollow bolt 14 (Fastening of the steering mechanism fig. see the car (with the amplifier)) fastenings and disconnect from картера the steering mechanism at first a pressure head highway 16, and then a returnable highway 12, having turned away a nut of its fastening. Muffle apertures in картере the steering mechanism, for example, plastic stoppers.
13. Remove highways.
14. Establish pressure head and returnable highways upside-down, using thus new sealing rings 13 and 15. Pay attention that at a returnable highway 12 sealant 13 round sections.

The prevention

The highway cannot bend strongly (diameter of a bend not less than 100 mm).


15. After installation add a working liquid and pump over hydraulic system of the amplifier of a steering (subsection 8.5.10 see).
16. Check up and, if necessary, adjust corners of installation of wheels.

The inhaling moments, Нм

Hollow bolt of fastening of a pressure head highway to картеру the steering mechanism
35
Nut of fastening of a pressure head highway to the pump
30
Nut of fastening of a returnable highway to картеру the steering mechanism
30
Bolts of fastening of a wheel
120